SCI-EXPANDED, SSCI VE AHCI DIŞINDAKİ ENDEKSLER TARAFINDAN TARANAN 24 YAYIN VE ATIF SAYILARI

Makale Künyesi

AA7075-T6 ve AZ31B Alaşımlarının Sürtünme Karıştırma Kaynağı Üzerinde Ön Isıtma ve Kuru Buz Soğutmasının Etkisi M Bilgin, Ş Karabulut, A Özdemir Politeknik Dergisi 22 (3), 655-663

Ş Karabulut, R Kökçan, M Bilgin, A Özdemir, Study on the Wire Electrical Discharge Machining of AA 7075 Aluminum Alloy  2018 9th International Conference on Mechanical and Aerospace Engineering

M Bilgin, Ş Karabulut, A Özdemir, Study on the mechanical properties of dissimilar friction stir welding of AA 7075 T6 and AZ31B Alloys 2018 9th International Conference on Mechanical and Aerospace Engineering

S Karabulut, A Sahinoglu, Effect of the cutting parameters on surface roughness, power consumption and machine noise in machining of R260 steel JOURNAL OF POLYTECHNIC-POLITEKNIK DERGISI 21 (1), 237-244

Ş Karabulut, A Şahinoğlu, R260 çeliklerinin işlenmesinde kesme parametrelerinin yüzey pürüzlülüğü, güç tüketimi ve makine gürültüsü üzerine etkileri Politeknik Dergisi 21 (1), 237-244

Ş Karabulut, H Karakoç, R Çitak, Effect of the B4C reinforcement ratio on surface roughness of A16061 based metal matrix composite in wire-EDM machining, 2017 8th International Conference on Mechanical and Aerospace Engineering

M BİLGİN, Ş KARABULUT, A ÖZDEMİR, Alüminyum Magnezyum Alaşımlarının Sürtünme Karıştırma Kaynağı İle Kaynak Edilebilirliğinin Değerlendirilmesi, Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji

Ş Karabulut, U Gökmen, H Karakoç, ÖK Kalkan, R Çıtak, Experimental Investigation of B4C Particulate Reinforced Aluminium 6061 Based Composite Material in Wire-Cut EDM

Ş Karabulut, A Güllü, Influence of Lead Angle Variation on the Coated Carbide Inserts Wear when Milling CGI and Modeling by Artificial Neural Networks and Regression Analysis Method Solid State Phenomena 220, 595-602

Ş Karabulut, A Gullu, An investigation of cutting forces and analytical modelling in milling compacted graphite iron with different lead angles

A GÜLLÜ, Ş KARABULUT, A GÜLDAŞ, Inconel 718 süper alaşımların işlenmesinde talaş kırılma problemleri ve talaş kırıcı tasarımı Gazi Üniversitesi Mühendislik Mimarlık Fakültesi Dergisi 23 (1), 157-164

A Gullu, Ş Karabulut, A Guldas, Chip breaking problems in machining of Inconel 718 super alloy and chip breaker design

M.Kademli, O.Y. Gulsoy (2013) - Investigation of Using Table Type Air Separators for Coal Cleaning - International Journal of Coal Preparation and Utilization 

M.Kademli, O.Y. Gulsoy (2012) - Role of Particle Size and Solid Contents of Feed on Mica – Feldspar Separation in Gravity Concentration 

M.Kademli, O.Y. Gulsoy (2016) -Influence Of Partıcle Sıze And Feed Rate On Coal Cleanıng In A Dry Separator - Physicochemical Problems Of Mineral Processing 

M. Kademli (2013) - Comparison of Sub-Sieving Techniques Based on the Relation of Particle Size and Specific Surface Area in Mineral Processing -  Particulate Science and Technology  

N.A. Aydogan, M.Kademli (2020) - Effect of operational conditions on Falcon concentrator performance with different particle size fractions -  Particulate Science And Technology 

M.Kademli, N.A. Aydoğan (2019) - An extraction of copper from recycling plant slag by using falcon concentrator - Gospodarka Surowcami Mineralnymi-Mineral Resources Management 

The Influence Of Ohmic Back Contacts On The Properties of a-Si:H  Schottky Diodes

Steady-State and Transient Photoconductivity in Hydrogenated Amorphous Silicon Nitride Films SCI 

“Optical Transmission Measurements On Glow-Discharge Amorphous Silicon Nitride Films”

BOLAT ÇİMEN CENNET, İPEK AHMET (2017) On Jacobsthal and the Jacobsthal-Lucas sedenions and several identities involving these numbers Mathematica Aeterna, Vol. 7, no. 4, 443 – 449

A Ipek, C Cimen On (p, q) Fibonacci Octonions,  Mathematica Æterna 6 (6), 923-932, 2016

Çimen, C., Ipek, A., & Çimen, E. (2019). On horadam sedenions. Journal of Science and Arts, 19(4), 887-898.